Full 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the truck arrives.
Before
After
Before
After
Before
AfterTrusted Garage Door Opener Repair & Installation for Kent Homeowners
A garage door opener that grinds, reverses, or refuses to respond turns a routine exit into a daily frustration. In Kent, where most homes built between 2015 and 2025 came with openers already installed, that means the unit sitting over your car is now 8 to 10 years old and entering its problem years. Servo Garage Doors Kent has repaired and replaced openers across Kent since 2015, from Panther Lake to East Hill, and also offers Kent Garage Door Opener Repair & Installation throughout the area. Our technicians carry OEM parts for LiftMaster, Chamberlain, Genie, and the other major brands on the truck, so most opener repairs are completed in a single visit. You get a flat written price before any work begins, and that price doesn’t change once the technician opens the housing. Call (425) 906-3489 and you’ll reach a live person, not a recording.
Key Takeaways: Garage Door Opener Repair & Installation in Kent
- The price range for opener repair in Kent is $120-$320; a full opener installation runs $250-$550, quoted in writing before work starts.
- Most opener repairs are same-day: our trucks carry the common failure parts (logic boards, gears, trolley carriages, limit switches) so you don’t wait on an order.
- We service all eight major brands: LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor.
- Our founding rule, now Clause 4 of The Haven Standard, is that the technician photographs the failed component before quoting a replacement. You see the evidence.
- Every visit ends with a documented photo record of findings and completed work delivered to you, plus a written warranty. That’s what leaving looks like.
What Our Garage Door Opener Repair & Installation Service Includes
An opener is a system, not a single part. When it fails, the cause is usually one of a half-dozen components, and finding the right one is what separates a fifty-dollar fix from a five-hundred-dollar guess. Here’s what we handle, and exactly what that means in a Kent garage.
Opener Repair
When a Kent homeowner calls about an opener that won’t open, the fault is most often the gear and sprocket assembly inside the motor housing, a stripped nylon gear that turns the metal worm drive. We replace it with the OEM part, not a generic substitute, because a gear with the wrong tooth count will announce itself within a month as a grinding noise. Our repair also covers the logic board, the circuit board that receives the signal from your remote or keypad; when a board fails after a power surge, the fix is a board replacement, not a new opener. Every repair starts with a diagnosis you can see: the technician opens the housing, photographs what’s broken, and shows you the photo before quoting the repair.
Opener Installation
When the opener is beyond repair, meaning a failed motor or a housing cracked by a falling spring, installation is the right call. We install belt-drive, chain-drive, and wall-mount openers, and we’ll tell you plainly which one fits your garage: belt-drive for attached garages where noise matters, chain-drive for detached garages where it doesn’t, wall-mount when you want the ceiling cleared. The install includes the opener, the safety sensors, the wall button, remotes, and programming, all covered by one written price. We haul away the old unit and test the door’s balance before mounting the new opener, because an opener bolted to an unbalanced door burns through travel gears within a year.
Smart Opener Upgrade
If your opener predates Wi-Fi, you don’t need a new motor; you need a smart retrofit. MyQ, Aladdin Connect, and Chamberlains’s built-in Wi-Fi lets you open, close, and monitor the door from a phone, which matters in Kent when you’re at the Kent Station and can’t remember whether you closed the door. We install the bridge or the Wi-Fi-enabled logic board, pair it with your network, and add the app to your phone before we leave. If you’ve already got a smart doorbell camera, we can integrate the opener into that system so one app handles both.
Keypad Entry
A wireless keypad outside the garage door adds a code, which means a way in without a remote, without a phone, and without leaving a key under a rock. We install and program keypads from LiftMaster, Chamberlain, and Genie, typically in about twenty minutes. We also repair existing keypads when the buttons stop registering, which is usually corrosion on the contact pad or a dead battery that has leaked. If the keypad is older than the opener, replacing it is usually cheaper than nursing it.
Remote Programming
Lost remote, new car, or a remote that only works when you hold it two inches from the antenna: programming is the fix, and it takes less time than this paragraph. We pair the remote to the opener’s receiver, clear old codes when you’ve lost a remote, and teach HomeLink or Car2U to talk to the opener from the steering wheel. When a remote stops working entirely, the problem may be the opener’s receiver board; we test the remote with a signal meter before replacing either part, so you don’t buy a remote you didn’t need.
Battery Backup
Kent’s fall windstorms knock out power to garages every year, and an opener without a battery backup is a locked door when you need it most. Many openers during the 2015 to 2020 build years in Kent didn’t ship with battery backup, especially on the Kent East Hill where garage doors face the prevailing wind. We retrofit the approved battery unit for LiftMaster, Chamberlain, and Genie openers, rated to open the door for 24 hours of standby with enough cycles to get a car in and out several times. When the power returns, the unit recharges automatically, and we set a reminder to replace the battery every three to five years.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Before
AfterBrands We Service for Garage Door Opener Repair & Installation
Servo Garage Doors Kent services all eight major opener brands: LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor. That’s not a marketing list; it’s what’s on the truck. Our technicians carry OEM logic boards, gears, remotes, and sensors for each brand, because a repair that requires two visits is a repair we didn’t prepare for.
We’ve worked on more LiftMaster and Chamberlain openers in Kent than any other make, which makes sense; they’re the most common in new construction and the most frequently installed by builders. When a LiftMaster 8500 wall-mount throws a limit-switch error, we know the fix, and we carry the switch. Genie units show up most often in Kent homes built before 2010, and we stock their older screw-drive parts as well as the newer belt-drive components. Craftsman openers, discontinued since 2018, still run in thousands of Kent garages; we keep their remotes and keypads in inventory and can cross-reference them to LiftMaster parts when the OEM stock is gone. Whether you have a Craftsman from the 2000s or a Raynor opener installed last year, we can fix it or replace it with a written price before we touch a screw.
Signs You Need Garage Door Opener Repair & Installation Right Now
- The opener runs but the door doesn’t move. This usually means a stripped gear, a broken coupler, or a trolley carriage that has jumped the rail. The motor is spinning, but none of that motion is reaching the door. Continuing to press the button just spins the gear and adds nothing; the repair is a part, not a reset.
- The door reverses on the way down for no reason. That’s the safety system doing its job, but the why matters. A misaligned photo eye, a scraped wire, or a failing logic board can all trip the reverse, and the longer it happens, the more strain goes into the traveler and gearbox. We diagnose the exact cause with a sensor alignment tool, not a guess.
- The opener grinds, whines, or clanks louder than it did last year. Opener noise in Kent garages often goes ignored because the door still opens. But a chain that has stretched, a belt fraying, or a gear chewing itself apart will not get quieter. Replacing the worn part now, at $120 to $320, is cheaper than replacing the motor it takes with it.
- The remote or keypad works only sometimes, or only from ten feet away. Intermittent reception is usually a receiver board on its way out or interference in the frequency band. If the remote works fine at the neighbor’s house, the problem is your opener, not the remote. We test with a signal meter to find out which.
- The opener is more than 12 years old and you’ve repaired it twice this year. At a certain point, the repairs add up to less than the remaining life of the unit. A new opener with a smart system and battery backup, installed for $250 to $550, may be the final repair. We’ll tell you the numbers and let the numbers decide.
Our Garage Door Opener Repair & Installation Process - Step by Step
Here’s exactly what happens when you call Servo Garage Doors Kent. This is the process Marcus Deller built the company around in 2015, and it has not changed since.
- 1
You call, a person answers. (425) 906-3489, 24 hours a day, including holidays. We ask what the opener is doing, what brand it is, and when it started. Then we give you a two-hour arrival window and text you the technician’s name when they’re on the way. No call centers, no callback windows.
- 2
The technician diagnoses the opener and photographs the failure. This is Clause 4 of The Haven Standard, and it’s the rule that started the company. The tech opens the motor housing, inspects the gear, logic board, trolley, and limit switches, and photographs the failed part. Before anything is quoted, you see the photograph and the tech explains what they found, in plain language.
- 3
You get a written price and written scope before any work begins. Clause 1 of The Haven Standard, and there are no exceptions. The price is flat, it includes parts and labor, and it is the price you pay at the end. If the tech finds something additional during the repair, you get a new written price before that work starts, not a surprise at the end.
- 4
The repair or installation is completed, tested, and documented. The tech runs a full open-close cycle test, checks the safety sensor alignment and force settings, and balances the door. Then they photograph the completed work. There is nothing left to guess about.
- 5
You receive the documented photo record and the written warranty. Before the technician leaves, you get a photo record of findings and completed work on your phone, plus the written warranty for the part and labor. The home team’s 365-Day Done Right Promise applies to every repair: if it’s not right, we make it right. That’s the paper trail. That’s what leaving looks like.
How Much Does Garage Door Opener Repair & Installation Cost in Kent?
A typical opener repair in Kent runs $120 to $320, depending on which part failed. A stripped gear is on the lower end; a failed logic board with programming is on the higher end. A full opener installation runs $250 to $550, which includes the new unit, mounting hardware, safety sensors, wall button, two remotes, programming, and haul-away of the old opener. A smart opener upgrade adding Wi-Fi and app control typically lands between $150 and $300 on top of the repair, depending on whether it needs a bridge or a new logic board.
What affects the price: the brand and age of your opener (discontinued models cost more because parts are scarcer), whether the door itself is balanced (an out-of-balance door must be corrected or it will destroy the new opener), and whether you’re adding accessories like a keypad or battery backup. What doesn’t affect the price: the technician’s mood, the time of day, or how nice your house is. The written price is the price.
A free estimate from us includes the diagnosis, the photograph of what we found, and a written price. If you have a written estimate from another company, bring it in and we’ll provide a Free Second Opinion on it, no coupon needed. If you want to see how that estimate compares to our Garage Door Opener Repair & Installation in Kent pricing, it’s on the page.
Garage Door Opener Repair & Installation Near Kent - Our Service Area
Servo Garage Doors Kent serves all of Kent, including Panther Lake, East Hill, the Scenic Hill area, and the valley, plus the surrounding communities: Garage Door Opener Repair & Installation in SeaTac, Garage Door Opener Repair & Installation in Auburn, Renton, Tukwila, Federal Way, Maple Valley, Burien, Newcastle, Sumner, Bonney Lake, and Issaquah. In Kent proper, most opener repairs are dispatched and completed within the same two-hour window; surrounding cities see typical arrivals within 90 to 120 minutes. When the opener demands attention at 2 a.m., we answer the phone and send a named technician.
Serving Kent, WA - Our Local Coverage Area
We’re based in the Kent area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
Frequently Asked Questions - Garage Door Opener Repair & Installation in Kent
Garage door opener repair means diagnosing and replacing a failed component inside or attached to the opener unit: a gear, a logic board, a belt, a chain, a limit switch, a sensor, or a remote receiver. Installation means replacing the entire opener with a new unit and setting it up so it opens, closes, and reverses correctly. In Kent, we do both, and the line between them is drawn by a photograph of the failed part and a written price for each option.
Most opener repairs in Kent are finished in 60 to 90 minutes because the tech arrives with the likely parts on the truck. A full installation, where we mount a new opener, install the sensors and wall button, and program the remotes, takes two to three hours. If the job is larger, you’ll know before we start, because the written scope includes the expected time.
Opener repair in Kent runs $120 to $320 for parts and labor, and installation runs $250 to $550 for the complete job. The difference depends on the part that failed and the opener’s brand and age. You get a flat written price before any work begins, and that number is the number, not an open-ended estimate. Call (425) 906-3489 and we’ll give you the range for your specific situation.
Yes. LiftMaster and Chamberlain are the most common opener brands in Kent, and Genie shows up regularly in homes built before 2010, so our trucks carry OEM parts for all three. We also service Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor. If your opener is a brand we didn’t name, call and ask; the odds are good we’ve repaired it before.
Yes. A garage door stuck closed at midnight with a car inside is an emergency, not an inconvenience, and we answer the phone 24 hours a day. You’ll speak to a person, get a named technician, and receive an on-the-way text. Emergency dispatch to Kent is available seven days a week, including holidays.
Every repair is covered by our 365-Day Done Right Promise: if it’s not right, we make it right, backed by The Haven Standard and a written warranty, not a handshake. The specific warranty term for a given part is stated in writing before the work starts. There is no fine print on page nine; the warranty is on the same sheet as the price.
Clear the area around the opener, about six feet back from the garage door track, and remove anything sitting directly under the opener unit. If you have a ladder, leave it out; if not, the tech has one. Have your remote and keypad available for testing if you have them. Nothing else is needed, we bring the parts, the tools, and the paperwork.
Schedule Your Garage Door Opener Repair & Installation Service in Kent Today
When your opener makes a noise it shouldn’t, or stops making any noise at all, the repair starts with a diagnosis you can see. Call (425) 906-3489 for a free estimate, a named technician, and a written price before any work begins. We answer the phone 24/7, including Kent holidays, and the photo record of what we found is yours before we touch a single screw.
Written by Marcus Deller, Owner at Servo Garage Doors Kent, serving Kent since 2015.